Home / Blog / Appliance / Home Appliances / Oven Not Working? 7 Common Causes and How to Fix Them
Oven Not Working — AVS technician testing an oven heating element with a multimeter.

Last updated: October 2026

Oven Not Working? ?Most ovens stop working because of a tripped or half-tripped circuit breaker, a control lock or delay-bake setting, a weak gas igniter, a burned-out bake element, a faulty temperature sensor, a door lock or thermal fuse problem after a self-clean cycle, or a failed control board. Start with power, settings and a reset. Most of the remaining causes need a technician.

 

What you noticeMost likely causeSection
The display works, but the oven won’t heatHalf-tripped breaker or bake element#1, #4
The oven went dead right after self-cleaningThermal fuse or thermal switchSelf-clean section
The door is locked and won’t openDoor lock after self-clean#6
A gas oven glows or clicks but won’t lightWeak igniter#3
The cooktop works, but the gas oven doesn’tOven igniter#3
Broil works, but bake doesn’tBake element#4
Food burns or stays raw at the set temperatureTemperature sensor or door gasket#5
An error code or “LOC” on the displayControl lock or control board#2, #7

Oven still not working? AVS repairs gas and electric ovens, stoves and ranges across Northern Virginia and Maryland. Call 703-457-9028 (VA) or 301-686-7129 (MD).

How to reset your oven

A simple power reset clears many electronic glitches, including lockouts after a power outage. Whirlpool recommends this process:

  1. Turn off the circuit breaker or fuse for the oven for one minute.
  2. Turn the breaker or fuse back on.
  3. Watch the oven for one minute to make sure the error code doesn’t come back.
  4. Check whether the oven heats normally.

If the power went out during a self-clean cycle and the cycle didn’t resume, KitchenAid suggests selecting “Self Clean,” then “Cancel,” waiting a couple of minutes, and trying again.

Quick checks before you call

  1. Check the breaker. Electric ovens use a double-pole breaker. Switch it fully off, then back on.
  2. Check the settings. Look for a control lock, “LOC” message or delay-bake timer that’s still set.
  3. Test the cooktop (gas ranges). If the cooktop burners light, gas is reaching the range, which points to the oven itself.
  4. Run a bake and broil test. Set the oven to Bake and see whether the bottom element glows or the burner lights. Then try Broil.

If you smell gas at any point, don’t use the oven. Leave your home and call your gas utility from outside.

1. No power: breaker, fuse or cord

What you’ll notice: The oven is completely dead, or the clock and lights work but the oven won’t heat.

Why it happens: Electric ovens run on 240 volts through a double-pole breaker. If only one side of that breaker trips, the display and controls can still run on 120 volts while the heating elements, which need the full 240 volts, won’t fire, as TC Appliances explains.

What you can do: Reset the breaker fully off and back on, and make sure the oven is plugged in securely. If the breaker trips again, stop and call a technician, since repeated trips point to an electrical fault.

 

2. Control lock or delay-bake setting is on

What you’ll notice: The oven ignores the controls, shows a lock symbol or “LOC,” or turns on later than expected.

Why it happens: Many ovens have a control lock for safety. A delay-bake or timed-cook setting left on can also stop the oven from starting when you expect it to.

What you can do: Check your owner’s manual for how to turn off the control lock and clear any timers. If that doesn’t work, try the power reset above.

 

3. Weak or failed gas igniter

What you’ll notice: A gas oven clicks, glows or takes a very long time to light, or never lights at all, even though the cooktop burners work.

Why it happens: Gas oven igniters wear out slowly. Fixify explains that an aging igniter can still glow, so it looks fine, but no longer draws enough current to open the safety gas valve. That’s why it’s so often misdiagnosed at home.

What you can do: Set the oven to Bake and watch through the broiler or bottom panel. Krupo Appliance Repair notes that the igniter should glow orange-white within about 90 seconds, and if it glows but no flame appears within 60 to 90 seconds, the igniter is weak and needs replacement, not cleaning. Igniter replacement involves gas components, so leave it to a technician.

 

4. Burned-out bake or broil element

What you’ll notice: An electric oven heats poorly or not at all, or only works on Broil.

Why it happens: The bake element at the bottom of the oven does most of the cooking, and it can burn out over time. Look for visible breaks, blisters or burn marks on the element. TC Appliances notes that if the broiler works but bake doesn’t, the bake element is the likely problem, and the same test works in reverse for the broil element.

What you can do: Run the bake and broil test with the oven empty and the light on. A damaged element needs replacing, which a technician can confirm with a quick electrical test.

 

5. Faulty temperature sensor

What you’ll notice: Food burns or stays raw at the set temperature, the oven heats and then gives up, or an error code appears.

Why it happens: The temperature sensor is the thin metal probe on the back wall of the oven. It tells the control board how hot the oven is. If it’s bent against the oven wall, damaged or failing, the oven heats incorrectly. Electrafix notes that a working sensor usually reads around 1,000 to 1,100 ohms at room temperature, though you should check your manual for the exact figure. A worn door gasket can cause similar symptoms by letting heat escape.

What you can do: Make sure the sensor isn’t touching the oven wall and check the door seal for gaps or tears. A technician can test the sensor and replace it if it’s out of range.

 

6. Door lock stuck after self-clean

What you’ll notice: The oven door stays locked, or the oven won’t start because the control thinks the door is locked.

Why it happens: Self-cleaning ovens lock the door during the cycle for safety. Whirlpool explains that the door unlocks once the oven cools to about 200 degrees Fahrenheit. If the cycle was interrupted by a power failure, the lock can stay engaged. AVS’s oven repair page also lists self-cleaning problems, such as a cycle that fails to finish or doesn’t heat up enough to clean the oven properly.

What you can do: Let the oven cool completely. Whirlpool suggests pressing Cancel/Off to start a latch reset and waiting 20 to 30 seconds, or turning off the breaker for one minute. On ovens with a manual latch, let the oven cool for 30 to 90 minutes before moving the latch. If the latch won’t move after the oven reaches room temperature, schedule service.

 

7. Failed thermostat or control board

What you’ll notice: Error codes, buttons that don’t respond, or an oven that won’t heat even though power, elements and settings check out.

Why it happens: The control board, or the thermostat on older models, tells the elements or burner when to turn on. When it fails, the oven may not respond at all or may heat erratically.

What you can do: Write down or photograph the error code, since codes differ from brand to brand, and share it with your technician. Control board replacement is a technician job.

 

Oven not working after self-clean? Check the thermal fuse

If your oven worked before a self-clean cycle and is completely dead afterward, the high heat may have tripped a safety device. According to Sears PartsDirect, some wall ovens have a resettable thermal switch with a red reset button on the back, while other models use a non-resettable thermal fuse that must be replaced once it blows.

Wilson & Myers notes that a blown thermal fuse after self-cleaning is one of the most common reasons an oven won’t turn on. Because the fuse sits behind the oven’s panels and protects against overheating, replacing it should be done by a technician who can also confirm what caused it to blow.

 

Gas vs electric oven: which causes apply to yours?

CauseGas ovenElectric oven
Tripped or half-tripped breakerControls and igniter can lose powerCommon cause of no heat
Control lock or delay settingYesYes
Weak or failed igniterMost common causeNot applicable
Burned-out bake or broil elementNot applicableCommon cause
Faulty temperature sensorYesYes
Door lock or thermal fuse after self-cleanYes, on self-clean modelsYes, on self-clean models
Control board failureYesYes

Oven and stove both not working?

If both the oven and the cooktop are dead, the problem is usually shared: the breaker or power cord for an electric range, or the gas supply or a control problem for a gas range. If only the cooktop has problems, see our guide to troubleshooting a gas or electric stove.

 

When to stop troubleshooting and call a technician

Call a technician if:

  • You smell gas (leave home first and call your gas utility)
  • The breaker trips again after a reset
  • You notice a burning or electrical smell
  • An element sparks or shows visible damage
  • An error code comes back after a reset
  • The door stays locked after the oven has fully cooled

Should you repair or replace your oven?

In most cases, repair is worth trying first. Mr. Appliance notes that stove and oven repair is often more affordable than replacing the entire unit, especially if the appliance is under 15 years old. Common fixes like igniters, bake elements, temperature sensors and thermal fuses are single-part repairs. If an older oven needs a control board and has other problems, it may be time to compare repair against replacement.

Check your oven before holiday cooking

Ovens tend to get their heaviest use around Thanksgiving and the winter holidays. Run a test bake a week or two before a big meal, so there’s time to schedule a repair if something’s wrong.

Why Northern Virginia homeowners call AVS for oven repair

AVS provides gas and electric oven, stove and range repair with prompt service, coming to your home or office throughout Northern Virginia and Montgomery and Prince George’s counties in Maryland. Our technicians handle ovens alongside the full range of household and commercial appliance repair, from refrigerators to dishwashers. Homeowners in Arlington can also see our local appliance repair in Arlington page.

  • Founded in 1991, serving the Washington DC metro area
  • Repairs for gas and electric ovens, stoves and ranges
  • Call 703-457-9028 (VA) or 301-686-7129 (MD)

Frequently Asked Questions

How long should an oven take to preheat?

About 12 to 15 minutes to reach 350 degrees, give or take five minutes, for ovens with a visible bake element, according to Whirlpool. Ovens with a hidden bake element take around 20 minutes, give or take five. Higher temperatures, unused racks left inside and opening the door during preheat all add time.

 

Why does my oven take longer to preheat in my condo or apartment?

It may be running on lower voltage. Whirlpool explains that a range installed on 208 volts instead of 240 volts takes longer to preheat, and that ovens in buildings with elevators are typically on 208 volts. Performance isn’t affected once the oven reaches the set temperature. It’s simply slower to get there.

 

Can I line the bottom of my oven with aluminum foil?

No. Whirlpool advises against covering an entire oven rack or the oven bottom with aluminum foil, silicone mats or similar materials, because it blocks good airflow. That can affect cooking and lengthen preheat times. Use a baking sheet on a lower rack to catch drips instead.

 

Why is my oven’s temperature off by a few degrees?

Many ovens can be recalibrated. Krupo Appliance Repair notes that a calibration adjustment is the first step when an oven runs slightly hot or cold, and the sensor should be tested only if that doesn’t fix it. Check your owner’s manual for the temperature offset setting.